Art Tech Page 43 Review

DPCAV

GUARDIAN 2D/3D INERTIAL STABILIZER (STANDALONE MODEL)

Instruction Manual	Click Me!
PC Software	Click Me!

Q: Why do I need the Guardian?, The Guardian helps both beginner and expert pilots fly with confidence, and provides two key modes of operation: In 2D flight mode, the Guardian provides much smoother flight and wing leveling stabilization for your model, which makes it a lot easier to adjust and fly your plane. The Guardian "remembers" level flight for your model and returns it to level flight when needed, as well as providing precise "fly by wire" control., The Guardian has two submodes for 3D flying: In 3D Heading Lock submode, simply center your sticks to have the Guardian lock onto your present attitude (pitch, roll, and heading), which can make it easier to perform stunts like prop hanging, inverted flight, knife edges, low speed harriers, etc. In 3D Gyro submode, the Guardian uses its built-in 3 axis gyro to increase your model’s stability, while leaving you in full control. In this mode the Guardian greatly reduces the effects of gusts, turbulence, motor torque and other factors, and can expand the maneuverability of your model in a variety of conditions., Q: I Fly FPV. Is the Guardian for me?, Q: Will the Guardian work with my model?, Q: How do I install the Guardian?, Q: How do I configure the Guardian?, Q: How does the Guardian work?, Q: What sets the Guardian apart from other Stabilization systems out there?, *Note: Using the PC software will require a common Micro-USB cable. Most likely you already have one of these, but it not then they are available from your local electronic/computer store.,

Based on Eagle Tree's proven inertial stabilization technology, the Guardian ...

DPCAV

DIGITAL OSCILLOSCOPE, 2-CHANNEL / 10MHZ (PORTABLE)

Analog Bandwidth	0 - 10MHz
Sensitivity	10mV/Div - 2V/Div
Resolution	8-bit
Input Impedance	1M ohm
Maximum Input voltage	50Vpk (for 1X probe) and 400Vpk (for 10X probe)
Coupling	DC, AC, GND
Max Real-time Sampling Rate	50MSps
Timebase	0.2us/Div - 10 minutes/div
Record Length	500 - 8000 points (each channel)
Run/Hold Modes	one button switchable
Trigger Modes	Auto, Normal, Single
Trigger Types	Rising/falling edge
Trigger Sources	Ch 1 or Ch 2
Trigger Position	0 - 100% of capture buffer
Supply Current	300mA @ 3.7V(LCD backlight ON, typical).
Dimension	140mm X 70mm X 30mm
Weight	190 gram (including battery)
Documents, firmware, and tools	Users Manual

Portable 2-Channel 10MHz Digital Oscilloscope:, This portable scope offers a lot of features at an affordable price. It has 2-channels with 10MHz analog bandwidth (50msps) and it includes a rechargeable battery pack. Two switchable 10X scope probes are provided too!, The DSO-094 has useful features that are not commonly found in other low cost oscilloscopes. For example: It can be placed in "Persistent Display" mode that keeps waveforms on screen until you erase them; This is very useful when combined with NORMAL trigger mode to capture and compare multiple waveforms that meet your trigger conditions., Features:, , Specifications:, , Number of Channels: 2,

This is a FACTORY ASSEMBLED scope; It is not a ...

ngHobbies

ADJUSTABLE 1AMP STEP-DOWN POWER REGULATOR

Input	6-23V
Output	3.3V, 5V, 9V or 12V (+/-5%)
Load	1000mA max
Efficiency	75-85% depending on load
Width	17.5mm
Height	5mm
Length	30.5mm
Weight	5 grams

Specifications:, , Dimensions:, Documentation:,

The New Generation Hobbies1A adjustable step down is a state ...

ngHobbies

FATSHARK MIG HEADTRACKER

Features:, Built in gyroscopic sensors, Weight:, 150 gr., Documentation:,

One of the most affordable and most feature rich headtracker ...

ngHobbies

AIRSPEED KIT WITH MPXV7002DP

Weight	0.1 oz; 4 g (Just the sensor)

The MPXV7002 is designed to measure positive and negative pressure. In addition, with an offset specifically at 2.5V instead of the conventional 0V, this new series allows to measure pressure up to 7kPa through each port for pressure sensing but also for vacuum sensing (refer to the transfer function in the data sheet for more detailed information). Features: -2 to 2 kPa (-0.3 to 0.3 psi). 0.5 to 4.5 V Output,

This is a stand-alone airspeed sensor. Includes Pitot Tube and ...

ngHobbies

OSD PRO SYSTEM 10HZ GPS, 150A ELOGGER V4 W/ WIRE LEADS

This is a ready to fly package with the following inside:, 1 x e-Logger V4 150A with integrated connectors., Manuals:, eLogger Manual,